Why Acura VSA System Light Is On? – 7 Reasons To Check
The VSA system keeps your car stable and maintains traction when accelerating, braking, or turning suddenly.
This technology instantly identifies any instability or loss of traction and then applies the brakes to specific wheels to keep the vehicle stable. It keeps track of wheel speed, steering angle, and lateral acceleration using sensors placed throughout your car.
Now the question is what does it mean when your acura vsa warning light become on. Is it safe to drive with VSA light on. Let’s have a look on this article to resolve your query.
VSA system prevents the car from sliding while making sharp turns.
What does the Acura VSA Light On Mean?
If the VSA light on your dashboard is on, the stability control system is not operating properly. Because of this, your car may be more likely to slide or crash during sharp bends or stops.
Now, is it safe to drive with vsa light on? No, you and your passengers may be in danger if you drive with the VSA light on, and it could also seriously damage your car.
Read Also: Why Check Engine, VSC, And Trac Off Warning Light Comes On?
Why Acura Check VSA System Light Become On – 7 Reasons To Check
The VSA light in your car could turn on for a variety of reasons. This is a list of the most typical causes:
1. Insufficient Brake Fluid
The hydraulic pressure created by the brake fluid is what drives the VSA system. There might not be enough pressure to operate the VSA system when the brake fluid level is low, turning on the warning light.
According to a report by Honda Motor Company, when the brake fluid level falls below a specified limit, the sensor sends a signal to the electronic control unit (ECU).
The ECU then turns on the VSA warning light on the dashboard to notify the driver of the low brake fluid level.
2. An Unreliable Steering Angle Sensor
In an Acura, the steering angle sensor detects the steering wheel’s angle and sends that information to the VSA control module. This determines the direction and amount of wheel rotation.
If the sensor is faulty, it can send incorrect signals to the VSA control module, which can affect the vehicle’s stability and trigger the warning light.
Related Post: Car Feels like It’s Dragging When I Accelerate:
3. Faulty VSA Modulator Control Unit
The VSA modulator control unit controls the hydraulic pressure in the braking system, which is essential for the efficient operation of the VSA system.
If the control unit malfunctions, it can cause a loss of hydraulic pressure or incorrect pressure regulation, which can affect the VSA system’s performance.
4. Low Battery Voltage
Low battery voltage can damage the VSA system’s capacity to receive and interpret information from the wheel speed sensors and control the brake pressure. This can result in the VSA light turning on in an Acura.
5. Wheel Speed Sensor Issues
The VSA system uses wheel speed sensors to assess each wheel’s speed and compare it to the other wheels to determine the direction and stability of the vehicle.
The VSA control module may interpret the data incorrectly and activate the warning light if one sensor gives the wrong signals.
6. Uniform Wheel Size
According to a study, if the wheel sizes on your car are not uniform, the rotational speed of each wheel can vary, which can trigger the VSA system. This can cause the VSA light to turn on.
7. Worn Brake Pads
The functionality of the ABS and VSA systems can be impacted by worn braking pads. When the brakes are applied, the ABS and VSA systems work together to maintain control and stability by modulating the brake pressure to each wheel. As a result, the VSA light may turn on to indicate a problem.
Related Post: Can Abs Cause Brake Pedal To Go To The Floor?
How to Fix Acura VSA Light Stays On Issue?
Now that you are aware of the several reasons why the VSA light can turn on, it is also crucial to be prepared for these scenarios. The solutions to the issues are listed in the table below.
| Problems | Fixes |
| Insufficient brake fluid | Inspect the brake fluid level and top it up if necessary |
| Damaged wheel speed sensors | Examine the connectors and wires for any damage. Replace the defective wheel speed sensor by contacting a mechanic |
| Uneven tire size | Make sure that all tires are the same size and are not damaged by wear and tear |
| Faulty VSA modulator control unit | You should take your car to a mechanic for a full evaluation and repair |
| Loss of stability | When it’s raining or slippery, you should drive carefully and within the speed limit |
| Low battery voltage | Recharge the battery of your automobile |
| Worn brake pads | Replace them with brand new brake pads |
How to Reset the Acura VSA Light?
By performing the following steps, you can reset the VSA system in your car:
- Step 1: After bringing the vehicle to a stop, take out the key from the ignition.
- Step 2: Open the hood and locate the fuse box. In most cars, it can be found next to the battery on the passenger side of the vehicle.
- Step 3: Remove the lid of the fuse box and look for the VSA system fuse. The fuse should have “VSA” or “Stability Control” written on it.
- Step 4: After that, disconnect the VSA fuse from the fuse box and wait for at least 30 seconds before reinstalling it.
- Step 5: Next, replace the cover of the fuse box and close the hood of your car.
- Step 6: Start the car and then wait a short while. If the reset is successful, the VSA light ought to turn off.
- Step 7: If the VSA light continues to stay on even after resetting the system, it is advised to have the vehicle serviced by a professional.
You can watch this YouTube video for a visual representation of this process. https://www.youtube.com/watch?v=y_whgmpn4oQ
Acura VSA light related (FAQs)
Read this section to have more insight regarding this matter.
1. Can I drive my Acura even with the VSA light on?
Yes. But while you can still operate your Acura with the VSA light on, you should practice caution, slow down, and get in touch with a professional as soon as possible.
2. What should I use for maintaining proper brake function and avoiding VSA problems?
You should invest in high-quality brake pads (Our Recommendation) because they eliminate dust and brake noise while delivering consistent stopping power.
3. How can I tell whether the VSA system in my Acura is operating correctly?
The VSA indicator light on your Acura dashboard will let you know if the VSA system is operating properly. This light should turn on briefly when you start the car and then go out. However, there can be a problem with the VSA system if the light stays on or flashes while you are driving.
in conclusion – vsa light
To conclude, the Acura VSA light is an essential safety element that can inform drivers of potential problems with their vehicle’s traction and stability control systems. There are many ways you can employ to get the VSA system working properly again.
However, the majority of these issues were resolved quickly and easily with the help of a mechanic. You can keep your Acura in good shape by being aware of the symptoms of a failing VSA system and doing routine maintenance.
Related Posts:
